|
NP - Self Clinching Fasteners - High Strength Studs
|
|
Self Clinching High Strength Studs provide a strong torque resistant captivated male thread in thin panels.
Unlike our Flush Head Clinch Studs these fasteners do not install flush on the back of the panel as they utilise a heavily castellated clinch feature to provide superior torque out and push out resistance.
Available in Steel and Stainless Steel from M5 - M10.
Also available in Phosphor Bronze for Bus-Bar applications.
Please Check for availability before specifying.
|
|
Also available with a dogpoint thread lead in (Type NHTSD). Call our sales office for details. |
|
Thread
& Pitch |
H
Max |
Min Sheet
Thickness |
Hole Size
in Panel
+ 0.1.3 - 0.0 |
S
Max |
D
± 0.25 |
Max
Mating
Hole |
Min C/L to
edge of panel |
M5 x 0.8* |
2.7 |
1.3 |
5.0 |
1.14 |
7.8 |
6.5 |
10.7 |
M6 x 1.0* |
2.8 |
1.5 |
6.0 |
1.27 |
9.4 |
7.5 |
11.5 |
M8 x 1.25 |
3.5 |
2.0 |
8.0 |
1.78 |
12.5 |
9.5 |
12.7 |
M10 x 1.5 |
4.1 |
2.3 |
10.0 |
2.29 |
15.7 |
11.5 |
13.7 |
Lengths |
Thread Size |
Length (L) ± 0.4 |
M5 x 0.8* |
15 |
20 |
25 |
30 |
35 |
40 |
45 |
50 |
M6 x 1.0* |
15 |
20 |
25 |
30 |
35 |
40 |
45 |
50 |
M8 x 1.25 |
15 |
20 |
25 |
30 |
35 |
40 |
45 |
50 |
M10 x 1.5 |
15 |
20 |
25 |
30 |
35 |
40 |
45 |
50 |
*Made to order only
Materials |
Finishes |
Carbon Steel (X)
300 Series Stainless Steel (A2)
Phosphor Bronze (PB)
|
Bright Zinc / Trivalent Clear Passivate (ZI)
Other finishes available to order |
The following installation panel material hardness
limitations apply when installing Self Clinching Studs.
Steel High Strength Studs: 85HRB Max
300 series Stainless High Strength Studs: 70HRB Max
Phosphor Bronze Studs: 55HRB Max |
Part Number Examples |
Type | Thread | Length | Finish
i.e. : NHTS-M8-15-ZI
(High Strength Stud - M8 x 10mm - Steel - BZP)
i.e. : NHTS-M10-20-A2
(High Strength Stud - M10 x 20mm - Stainless) |
|
|
|
Installation Guide
|
|
 |
Thread Size |
D
+ 0.08 |
Pocket Diameter in Punch
(Measure head diameter of fastener & add 0.5mm) |
M5 |
5.03 |
7.55 - 8.05 |
M6 |
6.03 |
9.15 - 9.65 |
M8 |
8.03 |
12.25 - 12.75 |
M10 |
10.03 |
15.45 - 15.95 |
First punch or drill the correct size hole. DO NOT deburr the hole prior to installation as this will remove material required during the clinching process. It is preferable to install the fastener from the side of the panel with the burring or blow through.
Place the fastener in the hole like in the diagram above making sure the part is seated squarely.
Apply a parallel squeezing force until the head is embedded flush in the panel.
When installing Self Clinching fasteners, please pay attention to the minimum hole centerline to edge and parent material hardness limitations.
For special applications or if you are unsure of any aspect about the usage or installation of this fastener, give our sales office a call and we will do our best to offer you a solution or give advice on your application.
|
|
|
Performance Data
|
Thread |
Fastener Material |
Max Nut
Tightening
Torque (Nm) |
Test Panel |
Panel
Hardness
(HRB) |
Installation
(kN) |
Pushout
(N) |
Torque
Out |
Tensile
Strength
(kN) |
M5 |
Steel |
4.4 |
1.5mm Aluminium |
15 |
13 |
800 |
5.4 |
12.8 |
Steel |
4.4 |
1.5mm Steel |
65 |
26 |
1500 |
7.6 |
12.8 |
Stainless |
4.4 |
1.6mm Aluminium |
35 |
12.4 |
800 |
5.4 |
7.3 |
Stainless |
4.4 |
1.5mm Steel |
54 |
21.7 |
1500 |
6.4 |
7.3 |
Phosphor Bronze |
3.47 |
1.5mm Copper CDA-110 |
28 |
15.6 |
1115 |
3.4 |
5.9 |
M6 |
Steel |
10 |
1.5mm Aluminium |
43 |
29 |
1270 |
14 |
18.1 |
Steel |
10 |
1.5mm Steel |
59 |
33 |
1750 |
14 |
18.1 |
Stainless |
10 |
1.6mm Aluminium |
35 |
15.4 |
1270 |
11 |
10.3 |
Stainless |
10 |
1.6mm Steel |
45 |
24.6 |
1750 |
11 |
10.3 |
Phosphor Bronze |
5.9 |
1.5mm Copper CDA-110 |
28 |
25.3 |
1600 |
6.7 |
8.3 |
M8 |
Steel |
21.7 |
2.3mm Aluminium |
39 |
35.6 |
1700 |
30 |
32.9 |
Steel |
21.7 |
2.3mm Steel |
58 |
44.5 |
2200 |
30 |
32.9 |
Stainless |
21.7 |
2.3mm Aluminium |
44 |
24.4 |
1700 |
20 |
18.8 |
Stainless |
21.7 |
2.5mm Steel |
43 |
37.8 |
2100 |
20 |
18.8 |
Phosphor Bronze |
1.3 |
3.2mm Copper CDA-110 |
32 |
33 |
2250 |
15.3 |
15.1 |
M10 |
Steel |
36.6 |
2.3mm Aluminium |
39 |
40 |
2445 |
36 |
52.2 |
Steel |
36.6 |
2.3mm Steel |
58 |
54 |
3470 |
49 |
52.2 |
Stainless |
36.6 |
2.3mm Aluminium |
44 |
33.3 |
2445 |
36 |
29.9 |
Stainless |
36.6 |
2.5mm Steel |
44 |
46.7 |
3470 |
36 |
29.9 |
Phosphor Bronze |
28.5 |
3.2mm Copper CDA-110 |
32 |
42 |
2500 |
25 |
24 |
The above data is based on average values obtained in a test environment. Variations in hole size, panel material and installation will effect performance. It is recommended that you carry out your own performance tests in the actual application. Contact our sales department who will be happy to supply samples free of charge.
|
|
|
İndir
Katalog - Broşür
|
